Contribute
Register

[SUCCESS] X79-UP4 IV-E B i7-4930K Geforce 9800 GTX

Status
Not open for further replies.
dondomingo

dondomingo

Joined
Mar 14, 2014
Messages
5
Motherboard
hackintosh
CPU
i7 3,5ghz
Graphics
gtx 780
Mac
  1. 0
Classic Mac
  1. 0
Mobile Phone
  1. 0
Hello World!

SETUP:
GA-X79-UP4 Rev 1.1 (bios needed F4)
IV-E B i7-4930K
Geforce 9800 GTX
TP-Link WDN4800
Crucial Ballistix 16gb 1600mhz
Samsung EVO 250gb

What you need for this build.
Mavericks 10.9.2
Champlist
Multibeast (mavericks)
Chameleon Wizard
UniBeast

Mavericks 10.9.2 downloaded from app store - UniBeast usb creater tool.
Download Mavericks, run UniBeast, plugin clean usb (min 8gb) and run the program.
When finished, make sure to put MultiBeast onto usb drive.

BIOS SETTINGS! IMPORTANT!
Getting the proper ram detection you will have to enter “advanced memory settings” and set X.M.P to “profile1”
Go to “advanced CPU Core Settings”
Make sure you disable
CPU EIST Function
CPU Enhanced Halt (C1E)
Next go to BIOS Features
Disable following
Full Screen Logo
Fast Boot
Limit CPUID Maximum
Intel Virtualization Technology
Intel VT-d
Intel I/OAT
Set Windows 8 features to “other OS”
Boot mode = legacy
Lan PXE = disabled
storage boot = legacy
Other lci device = legacy
Network stack = disabled
go to -> Peripherals
High Precision timer = Enabled
EHCI-Handoff = Enabled
XHCI-Handoff = Enabled
USB 3.0 Supoort = Disabled (XHCI Controller)
Make sure you're running all SATA ports as AHCI
Turn on HOTPLUG for every port
Under Peripherals go to gigabit network connection and
WAKE on LAN = disabled
Power management:
Wake on LAN from S5 = disabled
To get the installation going you will probably have to type in following bootflags

-v cpus=1 npci=0x2000 GraphicsEnabler=Yes or
-v cpus=1 npci=0x2000 GraphicsEnabler=No

See this is where i don't have a fix myself, but system will start, and run mavericks install - but seems to be very slow. Have patience.
 
[SUCCES] X79-UP4 IV-E B i7-4930K Geforce 9800 GTX

When install has finished, system will reboot - make sure to use boot flags again for the first startup.

Then go to multi beast - install:
Drivers:
Audio -> Realtek -> Without DSDT -> ALC892
Disk -> "3rd Party SATA" - and TRIM Enabler
MISC -> ElliottForceLegacyRTC, EvOreboot, FakeSMC v6.0.1123, VoodooTSCSync (6 core in my case)
Network -> Intel -> AppleIntelE1000e v3.0.4
System -> AppleRTC Patch for CMOS Reset

BOOTLOADERS:
Chimera v2.2.1

CUSTOMIZE:
Basic Boot Options
GraphicsEnabler=Yes
Hibernate Mode - Desktop
Use KernelCache

SSDT OPTIONS:
Sandy Bridge Core i5/i7 Overclocked
 
[SUCCES] X79-UP4 IV-E B i7-4930K Geforce 9800 GTX

Hi dondomingo
.​
I recently did my first hackintosh build by following egotrippin's guide.
http://www.tonymacx86.com/mavericks...abyte-x79-up4-3930k-gtx-690-ocz-vertex-3.html
I did everything and was able to boot normally with almost everything working, except for the display and sound. It's doing slow motion while i'm using it. (I did a video to show you what i mean.) Please help me solve this issue. And i also installed drivers and cuda enabler that i downloaded from nvidia, but it still didn't fix the problem. By the way my system is built with GA-x79-UP4 F5 + 4930k + Asus GTX 680 + 32GB 1866Mhz DDR3.

Here's the link to the video. I will appreciate much if you could help me on this.

https://vimeo.com/90064979

Thanks...
 
Hey sorry haven't been around for a while, hope you got your system going? if not - uhm you will have to install voodoosync and get the latest cuda driver - that will eventually fix the problem.

You will probably have to boot with cpus=1 but once you have installed your voodoosync kext make sure to remove the flags from org.boot.plist.

that should kill the problem no matter what.
t0olbox said:
Hi dondomingo
.​
I recently did my first hackintosh build by following egotrippin's guide.
http://www.tonymacx86.com/mavericks...abyte-x79-up4-3930k-gtx-690-ocz-vertex-3.html
I did everything and was able to boot normally with almost everything working, except for the display and sound. It's doing slow motion while i'm using it. (I did a video to show you what i mean.) Please help me solve this issue. And i also installed drivers and cuda enabler that i downloaded from nvidia, but it still didn't fix the problem. By the way my system is built with GA-x79-UP4 F5 + 4930k + Asus GTX 680 + 32GB 1866Mhz DDR3.

Here's the link to the video. I will appreciate much if you could help me on this.

https://vimeo.com/90064979

Thanks...
Click to expand...
 
Thanks for the reply. i got it fixed after installing chameleon wizard. i just tweaked on some graphics settings (which i already forgot..hehe..) then after rebooting it was all working fine.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top