ok, I tried to follow it closely, but will check again.... the one I am certain of is that I did not use the commands in terminal you listed in step 3.D. .... Should I try to enter those now? or are they already taken care of in the preferences/energy saver?
would you suggest to try...
tried retesting sleep, will not wake properly still (system powers up, but blank screen still).
also tried using another wired keyboard/mouse used on another hack build, same result.
while we are talking, is it OK to do these and other apple software updates, either now or later, for Mojave...
also just noticed that if I select "lock screen" instead of sleep from the apple menu the system will lock to login page and then become unresponsive (screen goes blank, cycles signal/no signal) and then goes to sleep but not wakeable with mouse press (power button blinks rapidly) and does not...
thanks again...
enabled Legacy ROMs.
put system to sleep.
the system powered up after clicking mouse but never revealed anything on screen, (monitor cycles between no signal and signal for a while but without any image from the system.. blank screen)
after about 5 minutes system went to...
Hi, thanks for your help....
the clover configurator indicated that for my i5-4590 to set the system def as 15,1 so that is what I went with, I do not have legacy option ROM enabled in setup, I do not have a AMD card installed (just the basic graphics).
Thanks for everyone's help in putting together this guide, it is amazing to have it so well laid out.
I am having difficulty with my (9020MT Mojave) machines sleep. it seems like it goes to sleep but reboots instead of waking normally. can someone please point me to where to look or what...
It was the age of my machine or OS... apparently the ivy bridge machine and or 10.6.8 will not make the unibeast USB so used a newer Imac running El Cap
Hi,
Getting this error after trying to create unibeast installer. "couldn't create USB installer" see image below
I have tried following all the troubleshooting suggestions (the mojave installer was downloaded using the macOS Mojave Patcher tool as i am running snow leopard on an older mac...
I found another SATA port on my motherboard and usded it (it was white instead of blue) and also In my bios I was able to change boot mode from efi to ACHI and it worked, I was able to see the drive, not sure which one did it but i suspect it was the bios change.
Hi Stork,
were you ever able to get usb 3.0 working properly/fully on your sandybridge system?
(I have a GA-Z68AP-D3 that I havent built yet and was going to buy a closeout i5-2500k for it if I knew I could get usb3 working properly).
I would most likely use Mountain Lion on it.
Thanks...
Hi Alex,
Were you able to get usb3.0 working properly with lion (or mountain lion now) on your i5-2500k Z68 sandy bridge system?
outside of multibeast was there anything special you needed to do to get it working ?
Thanks for the insight.
BigG
Re: optomize speed on the CustoMacmini 2011 w/Snow Leopard?
SOLVED
When I did the test i mention above, i looked to see what had changed during iBoot and saw that the system definition was now MacPro 3,1 in the 'about this mac' screens, (when previously i had installed the macmini 3,1...
Re: optomize speed on the CustoMacmini 2011 w/Snow Leopard?
edit:
looking in my /E folder and my bootlist generateC and Pstates =yes
As a test, I tried booting up the OS using iBoot, instead of directly from the HD.
When I do and then run Geekbench, the score goes up to 6111 (from my...
Re: optomize speed on the CustoMacmini 2011 w/Snow Leopard?
I did have C3/C6... state support 'enabled' in the bios originally but reset it to 'auto' with no effect
I have not tried manually adding any kexts (other than the 'basic' customacmini multibeast settings)
(Solved...see post below) For the life of me i have not been able to figure out why my Customacmini is getting low geekbench scores. When compared to other forum members I get a score of 3500 to their 6500+ scores with identical builds (EXCEPT for theirs running 10.7.2 and mine 10.6.8 and my...
Curious... has this build allowed you to use the onboard HD3000 Graphics with 10.6? So far I have been unable to use my 10.6.8 system without a discreet graphics card.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.